Study on inhomogeneous cooling behavior of extruded profile with unequal and large thicknesses during quenching using thermo-mechanical coupling model

The interfacial heat transfer coefficient between hot profile surface and cooling water was determined by using inverse heat conduction model combined with end quenching experiment. Then, a Deform-3D thermo-mechanical coupling model for simulating the on-line water quenching of extruded profile with unequal and large thicknesses was developed. The temperature field, residual stress field and distortion of profile during quenching were investigated systematically. The results show that heat transfer coefficient increases as water flow rate increases. The peak heat transfer coefficient with higher water flow rates appears at lower interface temperatures. The temperature distribution across the cross-section of profile during quenching is severe nonuniform and the maximum temperature difference is 300 °C at quenching time of 3.49 s. The temperature difference through the thickness of different parts of profile first increases sharply to a maximum value, and then gradually decreases. The temperature gradient increases obviously with the increase of thickness of parts. After quenching, there exist large residual stresses on the inner side of joints of profile and the two ends of part with thickness of 10 mm. The profile presents a twisting-type distortion across the cross-section under non-uniform cooling and the maximum twisting angle during quenching is 2.78°.     

Peanut FAD2 Genotype and Growing Location Interactions Significantly Affect the Level of Oleic Acid in Seeds

The level of oleic acid is an important parameter in determining seed nutritional quality and oil stability. The level of oleic acid in peanut is genetically controlled by a pair of fatty acid desaturase genes (FAD2A and FAD2B), but the environmental conditions of the production sites can also have a significant effect. To investigate the effect of gene and environment interaction, 45 accessions were grown at three locations for 2 years. Environmental data were collected; individual plants were genotyped with functional SNP markers from FAD2A and FAD2B; and seed level of oleic acid was determined by gas chromatography. Three FAD2A/FAD2B genotypes (448G/no insertion 442A, 448A/no insertion 442A, and 448A/insertion 442A) were identified and designated as G/W, A/W, and A/A, respectively. A/A genotype averaged the highest level of oleic acid (80.0%), followed by A/W (56.0%), and then G/W (40.7%). Analysis of gene and environment interaction revealed that oleic acid phenotype plasticity could be explained by the interaction of FAD2 genotype and photothermal time, which quantified environmental conditions. The A/W genotype was the most sensitive to photothermal time changes. The oleic acid plasticity revealed in this study would be useful for breeders, farmers, and product processors.     

空间红外大口径折射式低温镜头设计与验证

针对目标探测类空间红外相机大范围成像、高灵敏度探测、高精度定位等应用需求,文中提出采用像方远心光路和低温光学技术结合的解决方案,设计了物方视场角8°×8°、入瞳口径265 mm、工作温度200 K的像方远心折射式光学系统。镜头最大口径280 mm,采用多级分散的弹性支撑设计,解决大口径低温透镜装框、透镜组件支撑和镜头整体安装各环节的热应力卸载问题。在保证高刚度和低漏热的情况下,使低温下透镜的热应力对镜头能量集中度的影响降低到可接受范围内。镜头完成装调及室温下像质确认后,进行了力学振动试验,并将其制冷到200 K水平测试像质,测试结果表明,镜头能量集中度达到轴上75%,边缘视场72%。     

便携式飞行时间质谱仪的研制及其在石化污水系统挥发性有机物监测中的应用

近年来，国内的大气污染问题越来越严重，挥发性有机物（VOCs）的排放是其中一个重要原因。VOCs是臭氧和气溶胶的前驱物之一，在大气化学反应过程中扮演着极其重要的角色。本实验自行研制了一台基于真空紫外（VUV）灯的高分辨光电离飞行时间质谱仪（TOF MS），建立了一种新的VOCs稀释采样方法，并将其应用于石化行业污水处理系统VOCs的采样与分析。结果表明：隔油系统的3个池子基本没有测到高浓度的挥发性有机物，其中溶气气浮甲苯物质的质量浓度最高，为50.41 mg/L，其余组分的质量浓度大多数在0.1~1.0 mg/L之间；1#加氢和2#加氢隔油池有着类似的组分浓度，以1#加氢隔油池为例，二甲苯物质的质量浓度为10.60 mg/L，乙苯为52.33 mg/L，苯为59.80 mg/L；由于罐区隔油池没有加盖，处于露天状态，挥发性有机物气体容易向大气中扩散，并没有检测出较高浓度组分。可以看出，新式采样方法可有效地稀释定量样品，操作简便，减少了样品因闪蒸过程造成的VOCs损失，检出物质更丰富；同时，使用自行研制的TOF MS仪器能够快速检测不同装置污水处理系统的VOCs种类，将该仪器用于实际样品检测，发现化工企业大多数密闭的池子都含有苯系物、醚类等，但不同工艺的污水处理系统VOCs存在明显差异。该质谱仪适用于石化企业污水系统VOCs监测。     

大采高工作面过断层破碎带围岩控制技术研究

为了研究大采高工作面断层破碎带围岩控制技术,采用UDEC分别模拟工作面揭露断层前后围岩应力变化规律、揭露断层时覆岩运移规律。根据模拟结果可知,断层导致工作面应力呈"几"字型分布及顶底板变形量增大。在断层影响区域采用锚网索、单体液压支柱挑棚联合支护取得了良好的效果。     

并联有源滤波器的改进重复控制策略研究

针对三相整流负载产生的6k±1次谐波,提出静止坐标系下的改进型6k±1重复控制策略。同时将比例控制与改进型重复控制相结合,设计改进重复控制并联比例的复合控制结构。为减小改进重复控制中延时环节不为整数的影响,采用基于Lagrange插值近似的FIR滤波器逼近分数延时特性。最后对系统进行稳定性分析和详细设计方法进行推导。通过Matlab仿真验证改进重复控制策略能有效跟踪6k±1次谐波且具有良好的补偿效果,动态响应较快。     

Validation of Models Predicting Nucleation Rates from Induction Times and Metastable Zone Widths

Three approaches for estimation of nucleation rates from induction time and metastable zone width (MSZW) were validated based on directly measured nucleation rates for paracetamol in ethanol. To quantitatively predict nucleation kinetics using Kubota's methods it is necessary to know the minimum detectable number concentration of nuclei. This was found by determination of light transmission of a series of diluted suspensions of newly nucleated crystals where the size had already been assessed by optical reflection measurement (ORM). The measured nucleation rates strongly depended on both temperature and supersaturation. The Nyvlt method predicted nucleation rates in this system reasonably well; however, it gave slightly low estimates for all temperatures. The methods of Kubota provided nucleation rates that were low by an order of magnitude.     

Real‐time monitoring by proton relaxometry of radical polymerization reactions of acrylamide in aqueous solution

The potential of time‐domain nuclear magnetic resonance (TD‐NMR) for the real‐time monitoring of solution radical polymerizations is demonstrated. A model system composed of a redox‐pair initiator system, acrylamide as monomer and water as solvent was investigated. A second‐generation continuous wave free precession technique was employed to measure the longitudinal relaxation time constant (T₁) of the samples throughout the polymerization reactions. This parameter was shown to be sensitive to the reactant feed free‐radical enhancement of the water molecule relaxation time, making it a good probe to monitor monomer conversion in real time in an automated, non‐destructive fashion. It was found that the T₁ value was better than the transverse relaxation time constant (T₂) for describing the evolution of the polymerization reactions, due to its greater sensitivity to paramagnetic effects. The TD‐NMR signal variation observed was linked to the formation, propagation and termination steps of the radical polymerization kinetics scheme. These first results may contribute to the application of real‐time monitoring of radical polymerization reactions employing low‐cost and robust TD‐NMR spectrometers. © 2018 Society of Chemical Industry     

New approaches to determine the interface height of fire smoke based on a three-layer zone model and its verification in large confined space

Large confined space has high incidence of fires, which seriously threatens the safety of people working there. Understanding the distribution of smoke in such large space is critical to fire development prediction and smoke control. Three improved methods for the stratification interface prediction of fire smoke are developed, including of improved intra-variance, integral ratio and N-percentage methods. In these methods, the interface height is determined by the vertical temperature distribution based on a three-layer smoke zone model, which is an improvement of a two-layer zone model. Thereafter, the three improved methods are applied to several typical fire cases simulated CFD to predict the smoke interface, and their applicability and reliability are verified by comparison of the smoke stratification results with the filed simulation results. Results show that the three improved methods can effectively determine the location of the three-layer zone model's interface, and they have the ability to predict smoke interface for fires with different fire source types and ventilation conditions.